Ruptela - Installation Guide
Installing a GPS tracking device in your vehicle just isn't an advanced process, but it is crucial to take safety precautions, as such the installation ought to only be carried out by a qualified Auto Electrician. Usually, it takes roughly 2 hours to set it up relying on the complexity of the vehicle’s wiring construction. GPS machine installation (primary set up with no gasoline/temperature/door sensors connected), read the following instructions. Read more on the Do’s & Dont’s of GPS device installation at the tip of this doc. Screwdriver set, Plier, Multimeter and Wire Stripper/Cutter/Crimper. Before installing the gadget, you want to note down International Mobile Equipment Identity (IMEI) variety of the GPS tracking device and the SIM GSM quantity. Then insert the GPRS enabled SIM card to the machine. You might as well obtain the car addition template to file vehicle data. Then insert the GPRS enabled SIM card to the machine.
You could as well obtain the car addition template to file vehicle data. IMEI is a singular quantity to identify GSM, WCDMA, and iDEN cellphones, satellite telephones, in addition to some telematics units that works as a unique identification code. This 15-digit quantity is often printed both on the bottom of the GPS tracking unit or the machine case; you require IMEI to register the GPS tracking device on the fleet administration software. Red wire (of GPS machine) to one end and the power supply of the automobile to the other end of a 1Amp fuse. Secure the fuse to the instrument chord with a cable tie. Connect Black wire (-ve) on the harness to Chassis Ground (any bolt or wire with -ve energy). Connect Yellow ignition sense wire to the vehicle’s ignition source to assist observe ignition ON/OFF events. Please consult the vehicle wiring diagram to find the ignition wire.
You can verify the vehicle ignition wire by measuring the vehicle’s operating voltage whereas the engine is running. Once identified, join the ignition wire to the FUSE Box with a 3M Scotchlok so that it will snap into place and can get it correctly seated. Please seek advice from the connection diagram under, for iTag Pro a detailed view of the wires & connectivities. One of many quickest and the most effective place to mount a GPS tracking device or a GPS tracker is underneath the dashboard or an exterior location in a horizontal place with a clear view of the sky. It's possible you'll experiment with putting the tracking device at completely different locations on the automobile to determine one of the best reception for the desired level of concealment. If the gadget has external GPS antenna then place the antenna beneath the dashboard or wherever convenient using double-sided sticky-tape to make sure it’s firmly fixed there. Once you’ve placed the GPS tracker in the car, you’re all set.
Connect the wire socket and GPS/GSM antenna (of these with exterior antenna) to the GPS gadget. As quickly as the system is powered on, both green LEDs (GPS & communication) will flash on and off whereas trying to find alerts. When full signal strength is achieved, each LEDs will continuously illuminate. So as to validate functionality, we have to ring the GSM mobile variety of the SIM. If it rings or responds with a busy note, you possibly can safely assume that the system is functioning properly. If there is no response, you could have to re-insert the SIM card and check the wiring once more. Please Log into the platform together with your credentials to ensure the gadget communicates with the server. Note: Make it possible for the IMEI no’s & cell no’s you updated against the automobiles are appropriate. To keep away from mishaps whereas set up, be certain that the car ignition is turned off earlier than initiating wire connections. It's all the time advisable to disconnect the suitable jumpers /connections of vehicle’s energy supply throughout the GPS machine installation; this is to avoid brief circuits and wiring damages.
Ensure that the wires stay disconnected while mounting/dismounting the gadget. Secure all wiring with Scotchlok, cable connectors, and electrical insulation tapes. Never enable any bare wiring to stay uncovered; connections have to be least seen. Ensure extra insulation if wires go through a visible/exterior region, in order to keep away from brief circuit/wiring damages. GPS tracking devices could be mounted in a zone of restricted entry, so none has direct access to the instrument. Keep connecting wires as discreetly as possible, making it less visible and arduous to note. For the security of personnel, device & vehicle, keep away from connecting gadget wires to the board computers (ECU) or management items. Ensure that you just fasten wires to other wires/non-transferring elements and iTag Pro to not fasten near heat emitting and transferring objects as friction/heat emission might trigger sparks leading to short circuits. While connecting ignition wire confirm if it’s the real ignition wire (energy supply available solely when the ignition is on). Using a multimeter, check power movement by turning on/off the engine.